afther repair EasyJtag Suite ver.: 2.0.3.0 / wxWidgets 3.1.0-W-U started. Operating

KLMAG2GE4A-A002

TRY detect emmc sucses

EasyJtag Suite ver.: 2.0.3.0 / wxWidgets 3.1.0-W-U started.

Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.

Successfully connected to box on COM3

Box S/N: 02FFA0050E3xxxxx, ,FW Ver.: 01.52

Box Working Mode: JTAG Box.

Box Drivers version: 3.0.0.0, are OK

Z3X Card Serial : AA3C-DF3A , ver: 22

Z3X Card Activation [LG] : NOT ACTIVATED , ACTIVATE NOW

Z3X Card Activation [SAMS] : NOT ACTIVATED , ACTIVATE NOW

Z3X Card Activation [JTAG] : ACTIVATED

Z3X EasyJtag Software ver. 2.0.3.0

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 02FFA0050E37D43B, ,FW Ver.: 01.52

CMD Pullup Level:1155 mV

CMD Active Level:1577 mV

eMMC Device Information

EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 05/2005 Rev.0x56

EMMC NAME: 000000 , S/N: 537986854

EMMC NAME (HEX): 30303030303000

EMMC ROM1 (Main User Data) Capacity: 16384 MB

EMMC ROM2 (Boot Partition 1) Capacity: 512 kB

EMMC ROM3 (Boot Partition 2) Capacity: 512 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.

Backup saved: 000000_ 537986854_20150604_2039.extcsd

Done.

TRY REPAIR EMMC FIRWARE UPDATE SUCSES BUT HAVE ERROR

Running:SAMSUNG: eMMC firmware update...

Confirmed eMMC Part Number: KLMAG2GE4A-A002

Z3X EasyJtag Software ver. 2.0.3.0

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 02FFA0050E3xxxx, ,FW Ver.: 01.52

CMD Pullup Level:2093 mV

CMD Active Level:2629 mV

Setup firmware update mode, wait 2..30 sec...

Success!

Sending eMMC firmware...

Success!

Verifying eMMC firmware...

Success!

Flashing eMMC firmware...

Success!

Repairing eMMC CID...
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]

Done.



Z3X EasyJtag Software ver. 2.0.3.0

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 02FFA0050E3xxxx, ,FW Ver.: 01.52

CMD Pullup Level:2093 mV

CMD Active Level:2629 mV

Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]

Done.


PLEASE HELP SIR

THANKS before