mbacollegespune.in













Wednesday, 24 April 2013

21:15

T-Mobile myTouch 4G Slide (HTC Doubleshot) Unbrick, Unlock, IMEI, SuperCID repair supported Repairing bricked HTC MyTouch4G (PG5910000) is easy with the RIFF Box.

JItender Mehto    No comments


 Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.


Resurrector will reflash radio’s boot zone and will re-write PDA’s HBOOT version 1.44.1107.

There is option to reflash BOOT and RECOVERY zones.


To resurrect HTC MyTouch4G (PG5910000):


  •  Solder JTAG cable to HTC MyTouch4G (PG5910000) JTAG pads;

  •  Insert batter and connect USB Data cable;

  •  Make sure HTC MyTouch4G (PG5910000) is selected in the list of models;

  •  If you use only battery, press Power On key;

  •  Click Resurrect button;

  •  Wait till software signals a successful operation completion;

  •  Disconnect power supply, de-solder JTAG wires;



Now phone is in bootable condition, that is, even if it does not
start up normally you can flash it using known flashing methods.


To enter download mode:


  •  Disconnect PC cable;

  •  Insert battery;

  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.



.


t-mobile_mytouch_4g_slide
Read More
21:13

HTC Titan X310E (HTC Eternity) Unbrick, Unlock, IMEI and SuperCID repair supported Repairing bricked HTC Titan (PI3911000) is easy with the RIFF Box.

JItender Mehto    No comments


 Phone is auto powered on with USB Data Cable connected to the PC while
battery is connected. Please note, battery presense is required.


Some (or all) revisions of HTC Titan (PI3911000) boards have JTAG
interface disabled (that is enable MARM JTAG Fuse is blown in the MSM
chip). In this case the JTAG may be enabled only by firmware itself.
This is done by the DBL loader, so if DBL area is damanged and MCU has
JTAG Disable FUSE blown then there is no way to resurrect your phone via
JTAG interface. However, in this case you may use HTC Titan (PI3911000)
USB DLL version which does not require JTAG interface and does
resurrection procedure via USB cable.

Resurrector will reflash radio’s boot zone (except DBL area) and will
re-write PDA’s SPL. Additionally to SPL and Radio zones, the zone which
contains Model ID is re-flashed too. Thus after resurrection phone will
have Model ID = ‘PI3911000’.


To resurrect HTC Titan (PI3911000):


  •  Solder JTAG cable to HTC Titan (PI3911000) JTAG pads;

  •  Insert battery and connect USB Data cable;

  •  Make sure HTC Titan (PI3911000) is selected in the list of models;

  •  If you use only battery, press Power On key;

  •  Click Resurrect button;

  •  Wait till software signals a successful operation completion;

  •  Disconnect power supply, de-solder JTAG wires;



Now phone is in bootable condition, that is, even if it does not
start up normally you can flash it using known flashing methods.


To enter download mode:


  •  Disconnect PC cable;

  •  Insert battery;

  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.



.

htc_titan_x310
Read More
21:11

Samsung GT-S7500T Galaxy Ace Plus Unbrick – Dead boot repair supported Resurrecting Samsung S7500T is easy with RIFF Box.

JItender Mehto    No comments





Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on, so no
need to press any power-on buttons on the phone keypad.


To resurrect Samsung S7500T:


  •  Solder JTAG cable to Samsung S7500T JTAG pads;

  •  Insert USB Data cable into board and PC;

  •  Make sure Samsung S7500T is selected in the list of models;

  •  Click Resurrect button;

  •  Wait till software signals a successful operation completion;

  •  Disconnect power supply, de-solder JTAG wires;



Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using known flashing methods.


To enter download mode:


  •  Disconnect PC cable;

  •  Insert battery;

  •  Hold ‘Volume Down’ and ‘Home’ keys and press Power-On.



.


samsung_ace_plus
Read More
21:10

Samsung S5750e Wave575 Unbrick – Dead boot repair supported Resurrecting Samsung S5750E is easy with RIFF Box.

JItender Mehto    No comments


To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.


In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.


To resurrect Samsung S5750E:


  •  Solder JTAG cable to Samsung S5750E JTAG pads;

  •  Connect USB cable to phone and PC;

  •  Insert battery;

  •  Make sure Samsung S5750E is selected in the list of models;

  •  Click Resurrect button;

  •  Wait till software signals a successful operation completion;

  •  Disconnect USB cable, de-solder JTAG wires;



Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state. We used MultiLoader 5.64
version.


To enter download mode:


  •  Disconnect PC cable;

  •  Insert battery;

  •  Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.



s5750e
Read More
21:10

Samsung SCH-R530 Galaxy S III LTE Unbrick – Dead boot repair supported Repairing bricked Samsung R530 is easy with the RIFF Box.

JItender Mehto    No comments


The device is based on the Qualcomm MSM8960 chipset.


Note, one simple way to connect over JTAG – connect USB cable to PC and
insert battery. In this case phone is automatically powered on.


To resurrect Samsung R530:


  •  Solder JTAG cable to Samsung R530 JTAG pads;

  •  Connect USB cable to phone and PC;

  •  Insert battery;

  •  Make sure Samsung R530 is selected in the list of models;

  •  Click Resurrect button;

  •  Wait till software signals a successful operation completion;

  •  Disconnect USB cable, de-solder JTAG wires;



Now phone is in bootable condition, that is, even if it does not
start up normally, you can flash it using original Samsung downloader
software to restore it to the working state.


To enter download mode:


  •  Disconnect PC cable;

  •  Insert battery;

  •  Hold ‘Volume Down’ key and press Power-On.



.

samsung_galaxy_s_iii
Read More
21:05

RIFF JTAG - RIFF JTAG Manager v1.49, RIFF Box Firmware v1.35 released (Cortex-A15, Cortex-A5)

JItender Mehto    No comments




24.04.2013 RIFF JTAG - RIFF JTAG Manager v1.49, RIFF Box Firmware v1.35 released (Cortex-A15, Cortex-A5)

Whats new:

RIFF Box Firmware v1.35




  • Added support for Cortex-A15 and Cortex-A5 cores.

  • Fixed emergency script issue for multi-cored Cortex MCUs: it was executed after first core was halted.




Now it is executed after all core(s) (if specified by reset strategy) are processed (halted).



RIFF JTAG Manager v1.49




  • Added support for Cortex-A15 and Cortex-A5 cores.

  • New Popup balloon is added with hints about 'Dead Body ID is wrong' error.

  • Added Windows 8 support.

  • Added "RIFFBOX on the Network" button (BOX Service Page).

    User can easily visit some main RIFFBOX's internet locations.

  • Some new IDCODES added to the search engine (CTRL+F)




.
Read More
09:27

MIRACLE BOX UPDATE VER 1.46 (24-APrIL 2013) MIRACLE BOX WEEKLY UPDATES ON THE WAY

JItender Mehto    No comments

Read More
Subscribe to: Posts (Atom)

 

Copyright @ 2013-2015 Android Mobile Doctor.

Designed by Android Mobile Doctor | AMD MyBloggerLab